Page 1 of 2 12 LastLast
Results 1 to 25 of 36

Thread: Wiper Switch fix ideas

  1. #1

    Array
    Status
    Offline
    Join Date
    12-03-2011
    Posts
    5
    Location

    upstate sc
    Vehicle

    1991 Mitsubishi Mighty Max

    Wiper Switch fix ideas

    Hey guys I have a 91 MM and the wiper switch arm broke about half way down. Any DIY mods I can try without replacing the whole unit for 200 bucks? Looks aren't really a problem.

  2. #2


    Array
    Status
    Offline
    Join Date
    02-02-2012
    Posts
    42
    Location

    Bridgeville, DE
    Vehicle

    1988 Dodge Ram 50
    Engine

    G54B
    you could try putting a piece of allthread or dowel up through the center and using epoxy or gorilla glue to hold the whole thing together... did that once with my old Beretta

  3. #3

    Array
    Status
    Offline
    Join Date
    12-03-2011
    Posts
    5
    Location

    upstate sc
    Vehicle

    1991 Mitsubishi Mighty Max
    Quote Originally Posted by mllrtm79 View Post
    you could try putting a piece of allthread or dowel up through the center and using epoxy or gorilla glue to hold the whole thing together... did that once with my old Beretta
    I thought about gluing something but never thought about a dowel rod. also wasn't sure if the glue would hold or if I needed to add a clamp too.

  4. #4

    Array
    Status
    Offline
    Join Date
    12-03-2012
    Posts
    300
    Location

    Buckingham,VA
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    4G67
    Salvage yardor look on rock auto.com, or car-part.com and if any salvage yards online have it then you will know

  5. #5

    Array
    Status
    Offline
    Join Date
    12-03-2011
    Posts
    5
    Location

    upstate sc
    Vehicle

    1991 Mitsubishi Mighty Max
    Quote Originally Posted by mllrtm79 View Post
    you could try putting a piece of allthread or dowel up through the center and using epoxy or gorilla glue to hold the whole thing together... did that once with my old Beretta
    ok I didn't know about those links. I don't mind a few bucks for a used but 200+ is crazy for a thousand dollar truck. if not ill just glue and engineer something.

  6. #6

    Array
    Status
    Offline
    Join Date
    04-10-2011
    Posts
    256
    Location

    WA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    6G72
    If it's just the arm, I believe its held in place by a small set screw at the base, so you don't need the whole unit. They are usually pretty easy to find in salvage yards.

  7. #7

    Array
    Status
    Offline
    Join Date
    12-03-2011
    Posts
    5
    Location

    upstate sc
    Vehicle

    1991 Mitsubishi Mighty Max
    Quote Originally Posted by lush90 View Post
    If it's just the arm, I believe its held in place by a small set screw at the base, so you don't need the whole unit. They are usually pretty easy to find in salvage yards.
    that's what i was wanting to hear but i can't find the part. Do you have to remove anything from the column?

  8. #8



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,814
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Quote Originally Posted by crissguinn View Post
    ok I didn't know about those links. I don't mind a few bucks for a used but 200+ is crazy for a thousand dollar truck. if not ill just glue and engineer something.
    A thousand dollar truck?? Mine was that way once. Now I'm into it 53+ times or more. But it was worth every penny I spent. It has kept me in the garage for 3 years. The wife and I have never been happier..
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  9. #9

    Array
    Status
    Offline
    Join Date
    12-03-2012
    Posts
    300
    Location

    Buckingham,VA
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    4G67
    They are easy to remove,just tap out the set screw and pull out the arm and replace

  10. #10

    Array
    Status
    Offline
    Join Date
    12-03-2012
    Posts
    300
    Location

    Buckingham,VA
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    4G67
    Just looked on car-part.com and you can get the whole steering column for $50

  11. #11

    Array
    Status
    Offline
    Join Date
    12-03-2012
    Posts
    300
    Location

    Buckingham,VA
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    4G67
    Best bet is a salvage yard,cause ebay and rock auto is $200 plus dollars

  12. #12

    Array
    Status
    Offline
    Join Date
    12-03-2011
    Posts
    5
    Location

    upstate sc
    Vehicle

    1991 Mitsubishi Mighty Max
    Quote Originally Posted by 92bluemax View Post
    Best bet is a salvage yard,cause ebay and rock auto is $200 plus dollars
    thanks for all the responses. I'd pay 50 but not 200. I'll check around here and the links suggested. If not, i'll "modify" it. haha.

  13. #13

    Array
    Status
    Offline
    Join Date
    01-02-2013
    Posts
    75
    Location

    Stanwood, Wa.
    Vehicle

    1987 Mitsubishi Mighty Max
    Engine

    G54B
    I went to two U pull it type wrecking yards last weekend and looked at five MM/d50's. For all that I found two useable multi-switches, one 1st gen and one 2nd gen. All the rest were busted up in one way or another. These darn things look like a weak point in these rigs. It was easy enough getting the steering wheel off -- loosened the center nut and one good hit to the back with a hammer and it popped right off. One hint, to get the horn pad off, there's a phillips head screw on the bottom way down in back. Gotta take that off first.

  14. #14

    Array
    Status
    Offline
    Join Date
    12-03-2012
    Posts
    300
    Location

    Buckingham,VA
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    4G67
    mine has a headlight switch on one side and a simple wiper switch on the right

  15. #15

    Array
    Status
    Offline
    Join Date
    01-02-2013
    Posts
    75
    Location

    Stanwood, Wa.
    Vehicle

    1987 Mitsubishi Mighty Max
    Engine

    G54B
    I haven't had the time to dissect one of these yet. Can the individual switches be taken off the bracket and used on another bracket or it it forever a single connected unit?

  16. #16

    Array
    Status
    Offline
    Join Date
    12-03-2012
    Posts
    300
    Location

    Buckingham,VA
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    4G67
    I don't know on this truck,but on occasion I have pulled them down when I worked at a salvage yard and some was seperate...but if you look at the pic of this one it appears to be alltogether

  17. #17


    Array
    Status
    Offline
    Join Date
    12-06-2012
    Posts
    62
    Location

    Vacaville CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    I.D.K.?
    I got one in the junk yard for 2 dollars I can figure out how to get the old one off. might just drill it out, but I dont wnat to screw up the new one. Ill post a pic tomorrow

  18. #18

    Array
    Status
    Offline
    Join Date
    10-08-2012
    Posts
    371
    Location

    Cali
    Vehicle

    1988 Dodge Ram 50
    Engine

    G63B
    ^ thats wassup. mine's busted too and I cant find any in the local JYs. well it still works but feels like its gonna break every time i twist it. but yeah if u can get a pic up that'd be great. heck if u figure it out start a DIY thread on it, since I'm sure it'll come in handy in the future. thanks.

  19. #19


    Array
    Status
    Offline
    Join Date
    12-06-2012
    Posts
    62
    Location

    Vacaville CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    I.D.K.?
    wiper arm 2.jpgwiper arm.jpg this is the arm but I cant figure out how to get that little bolt or nut or screw out. any clues

  20. #20

    Array
    Status
    Offline
    Join Date
    10-08-2012
    Posts
    371
    Location

    Cali
    Vehicle

    1988 Dodge Ram 50
    Engine

    G63B
    idk but from the pic looks like thats all one assembly. doesnt look like that bolt/nut u referred to can come off.

  21. #21



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,814
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Bon't pull the bolt.. it's a wiper blade. The end is plastic. The arm has a U on the end. There is a little plastic release clip. You push it then slide the plastic end back toward the base of the arm. It is in the package with the new blade.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  22. #22

    Array
    Status
    Offline
    Join Date
    10-08-2012
    Posts
    371
    Location

    Cali
    Vehicle

    1988 Dodge Ram 50
    Engine

    G63B
    Quote Originally Posted by camoit View Post
    Bon't pull the bolt.. it's a wiper blade. The end is plastic. The arm has a U on the end. There is a little plastic release clip. You push it then slide the plastic end back toward the base of the arm. It is in the package with the new blade.
    i believe he was referring to the wiper switch not the blade. and thats what the pic looks like too (the switch assembly for the wipers)

  23. #23


    Array
    Status
    Offline
    Join Date
    12-06-2012
    Posts
    62
    Location

    Vacaville CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    I.D.K.?
    I dont think he even looked at the pictures lol

  24. #24

    Array
    Status
    Offline
    Join Date
    10-08-2012
    Posts
    371
    Location

    Cali
    Vehicle

    1988 Dodge Ram 50
    Engine

    G63B
    lol i think ur right.. he probably just glanced at it real quick and though it was the actual arm. its the beast at area 51 keepin the mad scientist hella busy haha

  25. #25

    Array
    Status
    Offline
    Join Date
    12-03-2012
    Posts
    300
    Location

    Buckingham,VA
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    4G67
    Quote Originally Posted by camoit View Post
    Bon't pull the bolt.. it's a wiper blade. The end is plastic. The arm has a U on the end. There is a little plastic release clip. You push it then slide the plastic end back toward the base of the arm. It is in the package with the new blade.
    That is the wiper switch on the steering column

Page 1 of 2 12 LastLast

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •