Results 1 to 6 of 6

Thread: how to pull check engine codes without a scanner

  1. #1

    Array
    Status
    Offline
    Join Date
    07-10-2013
    Posts
    14
    Location

    connecticut
    Vehicle

    1988 Dodge Ram 50
    Engine

    G64B

    how to pull check engine codes without a scanner

    Hey all,

    new to the forum, just inherited a 1988 ram 50 w/ 2.0 from elder next door neighbor that put 54k on the clock, body and all is great, engine clean and purrs, cept service light is on and stepping on gas beyond 1/2 way produces a nice bog down that I need to rectify, I think its a carb issue from things i've seen here already, but my question today is first how to pull the service codes without buying a scanner i may only need once, is there a ignition key cycling you can do to get the codes to flash the service light, or a pin key that will make the codes speak

    just don't wanna buy a scanner if there is a cheaper way

    thanks in advance

  2. #2



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,819
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    A scanner is not necessary. All you need is a volt meter with a needle. If you look in the manual section> over 216 manuals> look for the Haynes Manual. It covers your MM truck. In there is a step by step with pictures on what pins to use. All you do is count the swings of the needle and look them up. The EGR light comes on every 50,000 mile or so and needs to be reset. It's behind the speedo a tiny switch that you flip.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  3. #3

    Array
    Status
    Offline
    Join Date
    07-10-2013
    Posts
    14
    Location

    connecticut
    Vehicle

    1988 Dodge Ram 50
    Engine

    G64B
    ah OK, so it might be the 50k service light then........i'll check thanks

    not excited though about troubleshooting the carb

  4. #4



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,819
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Does it run OK?
    If so then it's probably going to be the light. All I know is the switch is in the dash on the right side near the gage cluster.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  5. #5



    Array
    Status
    Offline
    Join Date
    07-24-2012
    Posts
    2,363
    Location

    Washington State
    Vehicle

    1986 Mitsubishi Mighty Max
    Engine

    G63B
    Welcome to the forum, sounds like you got a good truck that can easily add 200k more miles.

  6. #6

    Array
    Status
    Offline
    Join Date
    03-16-2016
    Posts
    3
    Location

    Kokomo, IN
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    G63B

    Unhappy

    Quote Originally Posted by camoit View Post
    A scanner is not necessary. All you need is a volt meter with a needle. If you look in the manual section> over 216 manuals> look for the Haynes Manual. It covers your MM truck. In there is a step by step with pictures on what pins to use. All you do is count the swings of the needle and look them up. The EGR light comes on every 50,000 mile or so and needs to be reset. It's behind the speedo a tiny switch that you flip.
    Im have a little trouble finding the pictures for the pin connections in the book can someone point me in the right direction chapter or even the page.

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •