Page 5 of 5 FirstFirst ... 345
Results 101 to 119 of 119

Thread: DGheaders Performance header: New design tri-y 2.0 2.4 2.6 g63b 4g64 g54b

  1. #101

    Array
    Status
    Offline
    Join Date
    04-09-2014
    Posts
    550
    Location

    sheffield, vt
    Vehicle

    1978 Dodge D-50
    Engine

    G63B
    Quote Originally Posted by geezer101 View Post
    RRTT's headers are old school. They are some beautifully made and finished headers but I doubt you'll be finding a set of those gems in a hurry...I share Brads observations on the new design headers. I would think having #1 exhaust runner being that much longer will force the engine to pull more torque from that cylinder (might make it sound like a WRX - could be a good or bad thing depending on your allegiances )
    good eye geezer101....its a Doug Thorley TRI-Y HEADER

  2. #102

    Array
    Status
    Offline
    Join Date
    09-26-2014
    Posts
    494
    Location

    Ca
    Vehicle

    1993 Dodge Ram 50
    Engine

    4G64
    ??? are these EQUAL TUBES ???
    OH the humanity--- what???

  3. #103



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,814
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Quote Originally Posted by BradMph View Post
    are the pipes equal length, I hoped for something prettier I guess, but they look workable.

    Wondering about pulse collisions with unequal lengths/
    Well since 98% of the stock manifolds out there are cracked and have the same length pipes. I really don't think you need to worry about pulse collisions unless you are pushing 8000 RPM and the direction of flow is all one way. Also thats more important on the intake side because the fuel can fall out of suspension with a carb.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  4. #104

    Array
    Status
    Offline
    Join Date
    09-26-2014
    Posts
    494
    Location

    Ca
    Vehicle

    1993 Dodge Ram 50
    Engine

    4G64
    ^^ yep
    Last edited by claych; 12-14-2015 at 08:11 PM.

  5. #105

    Array
    Status
    Offline
    Join Date
    08-24-2013
    Posts
    187
    Location

    Alexander City, AL
    Vehicle

    1995 Mitsubishi Mighty Max
    Engine

    4G64
    I Want one!
    So did these get built and are available this time?
    Thanks for following through guys, its been a looong process for sure!

  6. #106

    Array
    Status
    Offline
    Join Date
    09-26-2014
    Posts
    494
    Location

    Ca
    Vehicle

    1993 Dodge Ram 50
    Engine

    4G64
    ^^^
    Ck HERE

  7. #107



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,814
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Quote Originally Posted by thillskier View Post
    I Want one!
    So did these get built and are available this time?
    Thanks for following through guys, its been a looong process for sure!

    I I think it has taken about 5 years to get them up and going. The paired port ones have had a totally new redesign now. So there much better fitting and looking.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  8. #108

    Array
    Status
    Offline
    Join Date
    02-03-2019
    Posts
    42
    Location

    Lawsonville, NC
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    4D55-T
    I know this is a little old. But do you make turbo header for the 2.4 4g64 SOHC engine. Mighty max head.

  9. #109

    Array
    Status
    Offline
    Join Date
    10-22-2019
    Posts
    24
    Location

    Morgan City, La
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    G64B
    Quote Originally Posted by Dcollins311 View Post
    I know this is a little old. But do you make turbo header for the 2.4 4g64 SOHC engine. Mighty max head.
    I second this.. I would buy two if you made them..

    I am looking for a stock one from down under right now.. Here is a photo of one I found on the board..
    Starion Turbo Manifold.jpg

  10. #110

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    The 2.0 SOHC G63B Starion manifolds aren't the only option but the alternatives aren't much better. Single cam Cordia turbo will work (notorious for cracking due to lean factory tune) or the manifold off a 2.0 DASH 12v turbo engine (better design manifold - split pulse) The whole engine is a near no brain swap - if you can find one. Much easier than a 4G63 twin cam (PLEASE DO NOT START THE "don't waste your time on a SOHC, blah, blah, etc..." TIRADE - this is minimal mod to retrofit alternative...) 83-87 Galant Cyclone turbo)

  11. #111

    Array
    Status
    Offline
    Join Date
    10-22-2019
    Posts
    24
    Location

    Morgan City, La
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    G64B
    Quote Originally Posted by geezer101 View Post
    The 2.0 SOHC G63B Starion manifolds aren't the only option but the alternatives aren't much better. Single cam Cordia turbo will work (notorious for cracking due to lean factory tune) or the manifold off a 2.0 DASH 12v turbo engine (better design manifold - split pulse) The whole engine is a near no brain swap - if you can find one. Much easier than a 4G63 twin cam (PLEASE DO NOT START THE "don't waste your time on a SOHC, blah, blah, etc..." TIRADE - this is minimal mod to retrofit alternative...) 83-87 Galant Cyclone turbo)
    I have access to both a dash engine right now and a cordia engine.. As both of those are hard to find I would still buy two manifolds if they would make them, One for my truck and one for the wife's truck.. If something happens later on I don't want to be looking for another unicorn! They have the plates and the tools they are almost there just some elbow grease needed to have a end product..

    I am not looking to make a 10 second truck I want to put taller gears in the rear end and have the power to not make it feel like a dog on the low end. Plus if I stick with the 8 valve head I have a non interference engine I don't have to worry about wrecking my investment with a timing misshap or broken belt. No reason why a 4g64 SOHC 8v should not be able to push 250 to 300 hp.

  12. #112

    Array
    Status
    Offline
    Join Date
    09-26-2014
    Posts
    494
    Location

    Ca
    Vehicle

    1993 Dodge Ram 50
    Engine

    4G64
    ^^
    Great post SamuelRock !!!
    Correct Me if My readings are in error -2'nd Gen sohc 4g64 s.e.f.i. mighty max-,
    Comp ratio 8:5-1
    Throttle Body 2 1/8 " (54 mm )
    Exhaust 1 7/8 " (48 mm)
    106 bhp (98 to the wheels)???


    Hypothetically,
    CR up by 1 point,
    TB id increase to 2 7/8 "
    Exhaust(cat back) 2 3/4 "
    = 131bhp, 119 to the wheels
    Net gain 20% over stock for the same undersquare design ?

  13. #113

    Array
    Status
    Offline
    Join Date
    10-22-2019
    Posts
    24
    Location

    Morgan City, La
    Vehicle

    1992 Mitsubishi Mighty Max
    Engine

    G64B
    Quote Originally Posted by claych View Post
    ^^
    Great post SamuelRock !!!
    Correct Me if My readings are in error -2'nd Gen sohc 4g64 s.e.f.i. mighty max-,
    Comp ratio 8:5-1
    Throttle Body 2 1/8 " (54 mm )
    Exhaust 1 7/8 " (48 mm)
    106 bhp (98 to the wheels)???


    Hypothetically,
    CR up by 1 point,
    TB id increase to 2 7/8 "
    Exhaust(cat back) 2 3/4 "
    = 131bhp, 119 to the wheels
    Net gain 20% over stock for the same undersquare design ?
    I think our truck HP is 116 out the box..

    I am thinking forged pistons and rods and 18# of boost from a 14B = 250 hp

    Do a Dana 44 swap on the rear end with 2.72 gears and kick back on the highway near 30mpg!

  14. #114

    Array
    Status
    Offline
    Join Date
    03-30-2019
    Posts
    7
    Location

    Hartselle AL
    Vehicle

    1987 Dodge Ram 50
    Engine

    G54B
    I am in the process of getting my engine 2.6 G54B rebuilt in my 87 D50 Ram pickup. I purchased the Weber carb today with the fuel pump and regulator from carbs unlimited. Also new distributor plugs hoses and some other stuff from Rockauto. I would be interested in the $500 header when I get the engine back.

  15. #115

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Not sure if he's still making them...

  16. #116

    Array
    Status
    Offline
    Join Date
    03-30-2019
    Posts
    7
    Location

    Hartselle AL
    Vehicle

    1987 Dodge Ram 50
    Engine

    G54B
    I will give him a call today to see if he is...

  17. #117

    Array
    Status
    Offline
    Join Date
    09-17-2022
    Posts
    2
    Location

    Rockwell, NC
    Vehicle

    1987 Mitsubishi Mighty Max
    Engine

    G54B
    Hope this is not a dead thread yet... Cannot find a header anywhere for the 2.6ltr 4X4. Anyone have any idea? Yep, its been a while I have been on this site.

  18. #118

    Array
    Status
    Offline
    Join Date
    05-15-2016
    Posts
    298
    Location

    Earth - California
    Vehicle

    1988 Mitsubishi Mighty Max
    Engine

    G54B
    Quote Originally Posted by Mise View Post
    Hope this is not a dead thread yet... Cannot find a header anywhere for the 2.6ltr 4X4. Anyone have any idea? Yep, its been a while I have been on this site.
    Looking for one as well.

  19. #119

    Array
    Status
    Offline
    Join Date
    08-09-2024
    Posts
    1
    Location

    Or
    Vehicle

    1986 Mitsubishi Mighty Max
    Engine

    G54B
    Hi

    New to the forum, however was able to find someone still making headers in 2024, for my 1985 2.6l MM 4x4 on the site.

    DG headers is still making these. Fitment was perfect and Dominic was easy and responsive to work with dgheaders@rocketmail.com

    see images of installed, don't mind the black coating that was me using boiled linseed oil, headers shipped raw mild steel.

Page 5 of 5 FirstFirst ... 345

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •