Results 1 to 13 of 13

Thread: front end steering parts 83-89 and 90-94. what changed?

  1. #1

    Array
    Status
    Offline
    Join Date
    06-10-2014
    Posts
    257
    Location

    Kingston Springs, TN
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G64

    front end steering parts 83-89 and 90-94. what changed?

    so i'm at the point of ordering a full new front suspension and after doing some searching now i'm just confused. i have two 2nd gen MM's a 1989 base model, and a 1994 sport. so for shits and giggle i looked up the front suspension for both of them and low and behold they list different parts. so i'm wondering if anyone knows what changed? i'm sure i could jack the sport up and crawl under and look but it's freezing cold out side and i figure someone's gotta know. what i have found is that 89-90 is the cut off point, something changed after that

  2. #2

    Array
    Status
    Offline
    Join Date
    11-23-2013
    Posts
    426
    Location

    pa
    Vehicle

    1988 Mitsubishi Mighty Max
    Engine

    G63B
    The outer tie rods are different size and power steering is diffrent.

  3. #3

    Array
    Status
    Offline
    Join Date
    06-10-2014
    Posts
    257
    Location

    Kingston Springs, TN
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G64
    So it's not like a upgraded system? Just a different variation? Was wondering if it would be worth it to upgrade the 89 to the 94 parts

  4. #4

    Array
    Status
    Offline
    Join Date
    07-14-2015
    Posts
    3
    Location

    Wi
    Vehicle

    1987 Dodge Ram 50
    Engine

    G54B
    Hi,
    I am in the process of changing my inner and oute

  5. #5

    Array
    Status
    Offline
    Join Date
    07-14-2015
    Posts
    3
    Location

    Wi
    Vehicle

    1987 Dodge Ram 50
    Engine

    G54B
    Hey,

    Sorry about that unfinished post that I put up yesterday.

    What I was trying to add to this post was: I am in the process of changing out my inner and outer tie rod ends on my 87 Ram 50 2wd. It seems that all parts are available for the 87 model, Passenger side inner & outer tie rod end, drivers side inner tie rod end. I haven't been able to find the drivers side outer tie rod end. All parts stores carry the right side outer tie rod end and list it as fitting both the left and the right side, which is wrong. The drivers side is left hand thread and the passengers side outer tie rod end is right hand thread. I picked up some outer ball joints for a 1990 Ram 50 and as another poster pointed out, the tie rod ends are bigger. Despite a bunch of searching I have come up with no solution...has anyone else run in to this issue and if so where can a guy find a left hand thread outer tie rod end for the left (drivers) side?
    Any help[ is appreciated.

  6. #6




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    RockAuto should have them.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  7. #7

    Array
    Status
    Offline
    Join Date
    07-18-2011
    Posts
    289
    Location

    Rockledge, PA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    4G64
    I got all my parts for my 90 on rock auto.

  8. #8

    Array
    Status
    Offline
    Join Date
    07-14-2015
    Posts
    3
    Location

    Wi
    Vehicle

    1987 Dodge Ram 50
    Engine

    G54B
    Ok, Thanks for the information.

    Do either of you remember if the tie rod ends were interchangeable between left and right side? Rock Auto lists the same part # that I got from Auto Zone (which I didn't have any luck with) but it is cheap enough that I am going to order 1 outer tie rod end and see how it goes.

    Again, thanks for the info!

  9. #9


    Array
    Status
    Offline
    Join Date
    08-31-2011
    Posts
    832
    Location

    Calgary, Alberta, Canada
    Vehicle

    1981 Dodge D-50
    Engine

    Ford V8
    the outer tie rod ends are the same it's the inner ones that are different.

  10. #10



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,507
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    Yup as Fordubishi said, inners are different, outers are the same. Just replaced all my steering and have done it multiple times before also.
    Josh
    09 BMW 335i E92 Twin turbo
    89 Macrocab 4g63 Turbo swapped & Bagged: Build Thread

  11. #11

    Array
    Status
    Offline
    Join Date
    03-26-2015
    Posts
    25
    Location

    Hawthorne, FL
    Vehicle

    1987 Dodge Ram 50
    Engine

    G63B
    Having the same issue. The right outer tie rod end (passanger side) 1987 *built 07/1986* is a left hand thread. Autozone Duralast es2194R is a right hand thread. Autozone says one part works on both sides...but nope. Mitsubishi warehouse has the same part number MA159984R and MA159984L for the front end.

  12. #12

    Array
    Status
    Offline
    Join Date
    03-26-2015
    Posts
    25
    Location

    Hawthorne, FL
    Vehicle

    1987 Dodge Ram 50
    Engine

    G63B
    Did a cross check at rockauto using the mitsubishi part number ma159984 and found one left hand thread: Delphi Part TA1116. Cross refrences to a Mitsubishi Staron.

  13. #13

    Array
    Status
    Offline
    Join Date
    03-26-2015
    Posts
    25
    Location

    Hawthorne, FL
    Vehicle

    1987 Dodge Ram 50
    Engine

    G63B
    NAPA
    Part Number: MRC ES2194R

    Specify Right Hand or Left Hand Thread for about $6.75 a piece. Going to NAPA. That Delphi Part at RockAuto is gonna be shipped from the Uk at 34.00 postage. No thanks.

    I be going to NAPA.

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •