Results 1 to 7 of 7

Thread: Red hot manifold

  1. #1

    Array
    Status
    Offline
    Join Date
    02-22-2015
    Posts
    6
    Location

    United States
    Vehicle

    1988 Mitsubishi Mighty Max
    Engine

    G63B

    Red hot manifold

    So I know these 2.0's put out huge power and its probably a normal problem for everyone (sarcasm if you didnt catch on).

    I picked up my 88 Mighty Max about 2 1/2 months ago and have been tinkering with it since I've had it here and there. One of the P/O actually put a Weber and elec fuel pump on already. I've owned older Fords since I've been 16, and just want to make sure everything is done right the first time with this truck. Im not used to such simplicity with the truck and I love it. Anyways I had to replace the elec fuel pump, put on a turn dial fuel press. reg. (for now, want to get one with a fuel return). I have the pressure reg set at 1.5 psi, turned down the fuel mixture scew to the carb. Im new to these Webers. I realize I could be running it lean, but it still diesels when i turn the engine off and a loud pop most of the time out of the tailpipe. So with it either running lean or timing could possibly be off, is there any advance that I have to unplug for timing and what is the factory spec?

    Thanks for the help.

  2. #2

    Array
    Status
    Offline
    Join Date
    08-11-2012
    Posts
    1,199
    Location

    Oakland, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    G63B
    With that little fuel and the manifold getting red hot, it's likely running dangerously lean, be careful. Bump fuel pressure up to 3-4 PSI and follow the lean best idle calibration. Factory spec is 5*BTDC, disconnect and cap the vac advance line. You can (usually) safely advance an additional 3-5* depending on the truck's mechanical condition but get it running well at 5* first.

    http://www.carburetion.com/Weber/adjust.htm

  3. #3



    Array
    Status
    Offline
    Join Date
    03-16-2011
    Posts
    3,823
    Location

    Sacramento, CA
    Vehicle

    1979 Dodge D-50
    Engine

    Chevy V6
    Plugged jet, low float level, but a Vacuum leek, Thats for sure.
    Only an Indy car should glow red hot. Perhaps you got one of "them" cross dressing D50's.
    Members come and members go, But the board keeps track of them.
    Find me on FaceBook
    clicking HERE.

    Or look on YouTube Click Here.
    http://mobilemillwright.com

  4. #4

    Array
    Status
    Offline
    Join Date
    04-09-2014
    Posts
    550
    Location

    sheffield, vt
    Vehicle

    1978 Dodge D-50
    Engine

    G63B

  5. #5

    Array
    Status
    Offline
    Join Date
    08-11-2012
    Posts
    1,199
    Location

    Oakland, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    G63B
    Read your plugs, too.

  6. #6

    Array
    Status
    Offline
    Join Date
    02-22-2015
    Posts
    6
    Location

    United States
    Vehicle

    1988 Mitsubishi Mighty Max
    Engine

    G63B
    Thanks for the help, I'm stuck at work right now but went out and set 3psi on the regulator, tuned the carb to a baseline to get home so I'm not running to lean/rich. When I get home I'll get out the timing light and check the plugs. Sorry if the post was confusing/all over the place, beer kinda sounded good after a long frustrating day haha.

  7. #7

    Array
    Status
    Offline
    Join Date
    08-11-2012
    Posts
    1,199
    Location

    Oakland, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    G63B
    Try this guide too if you're getting frustrated:

    http://www.carburetion.com/troubleshoot.htm

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •