Page 1 of 2 12 LastLast
Results 1 to 25 of 28

Thread: confused about a cable coming from the tranny

  1. #1

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B

    Lightbulb confused about a cable coming from the tranny

    {admin if i put this in wrong thread please put in correct one thanks}
    to start off with let me say thanks to any and all help on this issue.
    i have a 1988 dodge ram 50 sport with the 2.6l with automatic transmission.
    a few weeks ago i replaced my MITSUBISHI MIKUNI CARBURETOR
    with a Weber Carburetor-Weber Carb kit
    on the old factory carb there was a cable coming from underneath to the carb
    that had to do with the tranny i,m guessing
    i,m sure most of you know what that is i myself do not lol
    this is the weber i put on

    [top]Mitsunishi Dodge Mazda Genuine Weber Carburetor Conversion Kit Electric Choke

    [top] 32/36 DFEV Electric Chokes-l1600.jpg

    now the problem i,m having
    is there doesn't seem to be a place to hook the cable up on the new carb
    do need this cable hooked up?
    and if so how would i go about it?
    thanks for any and all advise

  2. #2

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    here is a few pics to give you an ideal of what i,m talking about
    DSC02575.jpgDSC02576.jpgDSC02577.jpgDSC02578.jpg

  3. #3

    Array
    Status
    Offline
    Join Date
    11-23-2013
    Posts
    426
    Location

    pa
    Vehicle

    1988 Mitsubishi Mighty Max
    Engine

    G63B

  4. #4

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    ok thxs for the info now for the $1000 question just what does it do? the cable i mean

  5. #5




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    it is the throttle position cable for the tranny - it tells the transmission how to shift by how much the gas pedal is depressed. If you don't hook it up and drive it a lot, you can damage the transmission. The u shaped bracket in the picture is the auto tranny kickdown lever.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  6. #6

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    ok makes that sense .
    i have only driven it a few times sense i have got it up and running and it shifted out real quick.
    so that made me think something was wrong lol
    thanks for the info now i have a starting place

  7. #7

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    does this kick down have anything to do with the overdrive?
    because i have noticed i can press the button and the light will come on and say od off but i don't hear or feel any change in the engine .
    is the overdrive a separate issue or will hooking the cable up also make the overdrive start working?

  8. #8

    Array
    Status
    Offline
    Join Date
    01-21-2014
    Posts
    29
    Location

    Brookings, OR
    Vehicle

    1988 Dodge Power Ram 50
    Engine

    6G72
    With that cable disconnected the trans will only "assume" that you are not pressing the gas enough to merit a downshift. OD should be independent of that, and it's possible that you weren't going the correct speed for it to want to shift into or out of overdrive. There are some better experts here than I for sure, but I'd wager that any OD issue that you have will not be related to the kickdown. Best to get that installed and working properly before trying to deal with the OD.

  9. #9

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    ok thanks speednsnake i wasn't sure if that was part of the overdrive or not i plan on working the drop down today then i will research the overdrive thanks for the info

  10. #10

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    ok update got out this morning and made a linkage to the kickdown cable seems to be working great shifting out just right now thanks to the adjustment bolt. now on to the overdrive when i,m going down the road say @ 55 mph and i reach up and press the button the light comes on but i don't feel anything change in speed or hear anything change in the motor sounds. can anyone tell me @ what speed the overdrive should kick in? thanks for any and all advise here are a few pics of my little girl
    DSC02579.jpgDSC02580.jpgDSC02581.jpgDSC02582.jpgDSC02583.jpgDSC02584.jpg

  11. #11




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    it should go into overdrive around 35 - 40 MPH. There is a sensor on the intake next to the carb that tells the tranny that the motor is warm enough to go into OD. That is a common fail Item - you can take that wire and ground it to the manifold to see if that makes the OD work
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  12. #12

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    ok i,ll start looking for the wire any ideals on what it might look like? and what the sensor looks like? thanks pennyman1 for the info

  13. #13




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    it will be a black wire and the sensor has a single 1/4" terminal on it.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  14. #14

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    i think i found the wire and the sensor will test it out tomorrow i had seen the sensor close to the carb right on top of the intake never really give it much thought i found a black wire that fit the sensor thanks for the help pennyman1 .

  15. #15

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    Another update fired the little girl up this morning took her for a ride hit the overdrive button and low and behold success.
    works and everything
    now i have another problem the speedometer needle started jumping around from 45-35 back to 45-50 mph so would that indicate a short?

  16. #16

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    just took it for a spin and everything seems to be working ok now could it have been because it was very cold this morning around 34 degrees .temp is around 51 now after the little trip down the road any thoughts?

  17. #17

    Array
    Status
    Offline
    Join Date
    12-21-2013
    Posts
    1,263
    Location

    Maurertown, Virginia
    Vehicle

    1990 Dodge D-50
    Engine

    4G64
    It's likely the speedo cable, and yes: they will bind up sometimes in very cold conditions...enough to cause exactly the unsteadiness you described. Since it isn't doing it in the warmer temps, worry not. The speedo cable is mechanical, not electrical, so there wouldn't be any shorting out.

    Kudos on getting things straightened out!!
    The greatest gift you have to give to the world is that of your own self~transformation.

  18. #18

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    thanks royster
    i hope something that i have posted will help someone else in the future.

  19. #19

    Array
    Status
    Offline
    Join Date
    12-21-2013
    Posts
    1,263
    Location

    Maurertown, Virginia
    Vehicle

    1990 Dodge D-50
    Engine

    4G64
    It likely will.

    Safe travels, my friend!
    The greatest gift you have to give to the world is that of your own self~transformation.

  20. #20



    Array
    Status
    Offline
    Join Date
    03-26-2011
    Posts
    1,507
    Location

    Vacaville, CA
    Vehicle

    1989 Mitsubishi Mighty Max
    Engine

    4G63-T
    if you keep having issues with bouncy speedo just unhook it from the back of the gauge cluster and lube it up by spraying some lube down the cable sheathe.
    Josh
    09 BMW 335i E92 Twin turbo
    89 Macrocab 4g63 Turbo swapped & Bagged: Build Thread

  21. #21

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    good ideal droppedmitsu i,ll keep that in mind so far it's only happening when it's real cold out after it warms up theres no problem i,m thinking the truck is telling me to move to some place warm lol

  22. #22

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    ok new issues lol
    finally got around to filling the gas tank all the way up just to find out that the fuel gauge is reading wrong. fuel tank reads 3/4 tank so before i get sit to pull the bed back off any ideals?

  23. #23

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    update on fuel reading wrong finally got the bed back off was all prepared to tackle the job this morning and wouldn't you know rain has moved in grrrrrrrrrrrrrrr o well @ least the tank got washed off lol
    hopefully i,ll be able to tackle it tomorrow.

  24. #24

    Array
    Status
    Offline
    Join Date
    03-19-2016
    Posts
    253
    Location

    clarksville, arkansas
    Vehicle

    1988 Dodge D-50
    Engine

    G54B
    well the weather was nice to me allowed me to get out and check the sending unit turns out all i needed to do was clean a contact and make a small adjustment.
    so now if someone want to donate a tank full of gas i can check to see if it's true on
    hope this helps someone out in the future
    DSC02602.jpg

  25. #25



    Array
    Status
    Offline
    Join Date
    07-24-2012
    Posts
    2,363
    Location

    Washington State
    Vehicle

    1986 Mitsubishi Mighty Max
    Engine

    G63B
    You could always grab the garden hose and fill it.

Page 1 of 2 12 LastLast

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •