Results 1 to 15 of 15

Thread: 4D55/6 ARP Head stud part numbers

  1. #1

    Array
    Status
    Offline
    Join Date
    12-24-2014
    Posts
    27
    Location

    Southern Idaho
    Vehicle

    1983 Dodge Power Ram 50
    Engine

    Other

    4D55/6 ARP Head stud part numbers

    I've never seen this published anywhere so here's for anyone wanting to get rid of the torque to yield bolts.

    ARP STUDS part # AU4.950-2UB

    ARP NUTS part # 300.8308

    ARP WASHERS part # 200.8500

    You will need 17 of each

    Jeff

  2. #2

    Array
    Status
    Offline
    Join Date
    12-24-2014
    Posts
    27
    Location

    Southern Idaho
    Vehicle

    1983 Dodge Power Ram 50
    Engine

    Other
    Correction 18 of each

  3. #3

    Array
    Status
    Offline
    Join Date
    03-29-2011
    Posts
    45
    Location

    Chattanooga, TN
    Vehicle

    1987 Mitsubishi Montero
    Engine

    4D55-T
    Might be a good idea to add this to the parts sticky

  4. #4

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Bumping/adding to this. I had been contacting ARP through email, they do not have anything documented for the 4d55/56, however from measurements, here are the numbers he gave me

    Stud
    Au4.600-2b m12x1.25 to m12x1.75 by 117mm
    $16.92 each

    Nut
    300-8376 m12x1.75
    $5.38 each

    Washer
    200-8500
    $1.19 each


    REVISED, As of current, the tech changed his mind after i asked about clamping force with the 1.75 threading, to which he replied that he agrees that he would not trust the 1.75 up top.
    Last edited by skullzaflare; 05-31-2018 at 09:20 AM.

  5. #5




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    That makes no sense - they are ARP studs, way stronger than any factory stud / bolt, and they don't trust it? Then why are they selling it?
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  6. #6

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Quote Originally Posted by pennyman1 View Post
    That makes no sense - they are ARP studs, way stronger than any factory stud / bolt, and they don't trust it? Then why are they selling it?
    You know how there are 'experts' who 'know' what they're doing? I would think that ARP's tensile strength testing of 170,000 psi would be up for it (304 stainless - the UTS version of the same studs are rated 270,000 psi) The, err, 'best' chinese equivalent would be down at least 30% of those figures...

    http://arp-bolts.com/p/technical.php

  7. #7

    Array
    Status
    Offline
    Join Date
    06-12-2015
    Posts
    185
    Location

    Owensboro, KY
    Vehicle

    1991 Dodge Ram 50
    Engine

    4D56-T
    I bought a set from them, the guy I spoke to said that that part number was made from there 200,000 PSI tensile strength ARP2000 steel. He asked what I was using it for and said they ought to hold up great. I've been running them now for about 6 months with no problem, just wondering how my factory turbo is holding so much boost...

  8. #8

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Quote Originally Posted by dancinggecko View Post
    ...just wondering how my factory turbo is holding so much boost...
    You know that Mitsubishi turbos get sourced as replacements for use on other vehicles? The Porsche guys rip the KKK turbos off their engines and use factory Evo ones, too funny
    (don't know if it's because the Mitsu turbos are geniunely superior or they feel bad about getting their asses handed to them by guys in Evos and will try anything )

  9. #9

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by pennyman1 View Post
    That makes no sense - they are ARP studs, way stronger than any factory stud / bolt, and they don't trust it? Then why are they selling it?
    The thought is, those studs i listed are being flipped over and used the wrong way.
    12x1.75 into the block would be using all the threads, but flipped it will only have a 3/4" nut on it. Far less surface area to grab than a 12x1.25
    Quote Originally Posted by geezer101 View Post
    You know that Mitsubishi turbos get sourced as replacements for use on other vehicles? The Porsche guys rip the KKK turbos off their engines and use factory Evo ones, too funny
    (don't know if it's because the Mitsu turbos are geniunely superior or they feel bad about getting their asses handed to them by guys in Evos and will try anything )
    They do last a lot longer than most turbos, side note the stock turbo didnt even last a week at 30psi, but thats because i dropped throttle to fast in a quick panic and bent all the blades

  10. #10

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by JeffTheMarine View Post
    I've never seen this published anywhere so here's for anyone wanting to get rid of the torque to yield bolts.

    ARP STUDS part # AU4.950-2UB (Only part number i have found and to be sold in singles)

    ARP NUTS part # 300.8308 (OP is sold in singles), 300-8328 (pairs), 300-8338 (10 pack of same nuts)

    ARP WASHERS part # 200.8500(OP is sold in singles), 200-8537 (10 pack of same washers)

    You will need 17 of each

    Jeff
    Going to add extra info in here
    Prices i have found.

    Autoplicity
    Stud AU4.950-2UB $12.87/ea

    Single nut 300-8308 $5.80/ea
    2-pack nut 300-8328 $8.14 ($4.07/ea)
    10-pack nut 300-8338 $43.01 ($4.30/ea)

    Single washer 200-8500 $3.99/ea
    10-pack washer 200-8537 $9.37 ($0.94/ea)

    SummitRacing
    Stud AU4.950-2UB $26.99/ea

    Single nut 300-8308 $3.99/ea
    2-pack nut 300-8328 $8.99 ($4.49/ea)
    10-pack nut 300-8338 $41.99 ($4.19.ea)

    Single washer 200-8500 $1.99/ea
    10-pack washer 200-8537 $8.99 ($0.89/ea)


    For some reason the single nut is the best deal on summit in singles....as dumb as that sounds
    Directly from ARP i was told through phone sales i can get the stud for $17.79/ea, single nuts $5.38/ea, and single washers for $1.19/ea. Now finding numbers for the 2 and 10 packs, it MIGHT be a better deal directly through ARP for that, but i cant say for sure.

    Dont forget the recommended lube (not for your wallet) 100-9908

  11. #11

    Array
    Status
    Offline
    Join Date
    04-13-2018
    Posts
    26
    Location

    Alberta canada
    Vehicle

    1991 Mitsubishi Pajero
    Engine

    4D56-T
    As far as I know the 4d56 do not use TTY head bolts. Do I have bad info?

  12. #12

    Array
    Status
    Offline
    Join Date
    01-18-2015
    Posts
    250
    Location

    Inwood WV
    Vehicle

    1991 Mitsubishi L200
    Engine

    4D56-T
    Quote Originally Posted by weelsey View Post
    As far as I know the 4d56 do not use TTY head bolts. Do I have bad info?
    i have had mixed results in my research, but a the same time 3 separate retorques i have had bolts come loose

    Now to be fair i am running 2 turbos and 30 psi lol, i went through 2 headgaskets in less than a month, no issues since ARP

  13. #13

    Array
    Status
    Offline
    Join Date
    02-06-2020
    Posts
    21
    Location

    salt lake city, UT
    Vehicle

    1983 Mitsubishi Mighty Max
    Engine

    4D56-T
    does anyone know the ARP kit number for these? i was told the 207-4205 kit might work.

  14. #14

    Array
    Status
    Offline
    Join Date
    06-12-2015
    Posts
    185
    Location

    Owensboro, KY
    Vehicle

    1991 Dodge Ram 50
    Engine

    4D56-T
    I don't believe there is a kit number for this. I just called them and gave them the part numbers I needed

  15. #15

    Array
    Status
    Offline
    Join Date
    04-13-2018
    Posts
    26
    Location

    Alberta canada
    Vehicle

    1991 Mitsubishi Pajero
    Engine

    4D56-T
    Quote Originally Posted by skullzaflare View Post
    i have had mixed results in my research, but a the same time 3 separate retorques i have had bolts come loose

    Now to be fair i am running 2 turbos and 30 psi lol, i went through 2 headgaskets in less than a month, no issues since ARP
    And we should be running the updated 4d56t head gaskets.

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •