Page 1 of 2 12 LastLast
Results 1 to 25 of 30

Thread: 1993 Mighty Max 2wd power steering conversion, possible?

  1. #1

    Array
    Status
    Offline
    Join Date
    06-11-2014
    Posts
    58
    Location

    Atlanta,GA
    Vehicle

    1993 Mitsubishi Mighty Max
    Engine

    4G64

    1993 Mighty Max 2wd power steering conversion, possible?

    Hi all,

    Recently I have been thinking of doing a power steering conversion to my 1993 Mighty Max 2WD which originally came with manual steering.

    Is there any direct bolt on ways to do it?

    Is it possible to just use 4WD's steering gear box and power steering pump? Is there any power steering pump bracket I can directly bolt on ?

    Any suggestions?

    Thanx in advance~

  2. #2

    Array
    Status
    Offline
    Join Date
    01-24-2017
    Posts
    1,219
    Location

    New Zealand
    Vehicle

    1981 Mitsubishi L200
    Engine

    Other
    Hey I have a power steering conversion done to my 1st gen. The box just bolts right in. You can use pretty much any Mitsubishi power steering box of that era - 1st gen Pajero/Montero should be the same, 2nd gen mighty max, Galants etc.
    The box body and arm is all the same, its just the top section that's different (its actually shorter which is why it was done to my truck to clear the exhaust manifolds on the v6), here in nz a lot of the 2nd gen trucks were power steer and that's where my box came from

    I cant help with the pump as my engine is not a Mitsubishi. , I would imagine you can use the 4wd one with out any issue

  3. #3




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    the steering boxes from the 2wd and 4wd trucks are the same for the 2nd gen, with no mods to the steering shaft from the column. The bracket for the pump and the pulleys to make it work have to come from the 4g64 motor, as they are different from the 2.6 motor. The lines are going to depend on the vehicle the steering parts come off of.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  4. #4

    Array
    Status
    Offline
    Join Date
    06-11-2014
    Posts
    58
    Location

    Atlanta,GA
    Vehicle

    1993 Mitsubishi Mighty Max
    Engine

    4G64
    So you are saying using pump and pulley from a 4g64 motor, say galant, and use 4wd mighty max steering box?

  5. #5




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    4g64 truck - car motors are different brackets and maybe pumps as well
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  6. #6

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    It depends on the belt layout but the FWD engines all use low profile pulleys to keep everything as close to the timing cover as possible. The power steering pulley usually piggybacks off the water pump pulley. Maybe look at a 2.4 Starwagon/Express van engine with PS and look at the layout in that as an option.

  7. #7

    Array
    Status
    Offline
    Join Date
    01-29-2018
    Posts
    5
    Location

    Illinois
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    4G64
    Can anyone elaborate as to the differences between the inside/outside mounted gearboxes? Does anyone know when this was made a model year change, and what models apply?

  8. #8




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    86 and older first gens are inside of the frame, late 86 to 96 are outside of the frame.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  9. #9

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    Had a question. I have a 90' MM with a 2.6L installed to replace the 2.4L. To add power steering do I just need to find a 4wd truck with power steering?

  10. #10




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    is your truck 2wd or 4wd?
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  11. #11

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    My truck is a 2WD. I was thinking i could harvest everything I need from a 2.6L 4WD truck with the exception of the steering box unless the 4WD box would work on a 2WD.

  12. #12




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    if it is off an 87 up truck, all the steering boxes are the same, 2wd and 4wd. Pitman arm may be different.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  13. #13

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    Can I use the pitman arm from my manual box? The steering system is still that of a 1990 it's just a 2.6L engine now.

  14. #14

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    I read on this site that the 4wd steering box won't work on a 2wd. It won't bolt up.

  15. #15




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    Maybe I am wrong - I thought they were the same but the pitman arm...
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  16. #16

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    Is there any one we can ask to confirm?

  17. #17




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    I have an 89 with power steering on it 2wd I am parting out very soon. It has the 2.6 though, so you will need the correct pump, bracket, and water pump pulley for the 2.4 motor you have. The hoses may work with the 2.4 pump location - I am not sure about that.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  18. #18

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    I need all the power steering parts for the 89 you are parting out. Mine has the 2.6 but in a 90 2WD frame.

  19. #19




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    Ok - its on the list to pull, so I will keep it all together.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  20. #20

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    Pennyman1, your inbox capacity is full.

  21. #21

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    I plan to post pics when the truck is done. All I have left is a small punch list of items to take care of and to add PS.

  22. #22




    Array
    Status
    Offline
    Join Date
    03-20-2011
    Posts
    4,857
    Location

    Pittsburgh, PA
    Vehicle

    1980 Dodge D-50
    Engine

    G54B
    I fixed the inbox.
    Pennyman1
    The best Dodge that Dodge never made
    Living the D-50 lifestyle since 1980

  23. #23

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    20190612_194636.jpg

    Got it done.

  24. #24

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    Getting ready to put power steering from a 87' 2wd on it. Are there any know conversion issues?

  25. #25

    Array
    Status
    Offline
    Join Date
    08-20-2017
    Posts
    63
    Location

    Lynchburg, VA
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    G54B
    This is a 90' with a 2.6L swapped in. I harvested a PS setup from a 87' 2WD with a 2.6L. I haven't started the conversation but was assuming it would be straight forward. I already have the pulley on my engine for the PS pump belt.

Page 1 of 2 12 LastLast

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •