Page 3 of 3 FirstFirst 123
Results 51 to 68 of 68

Thread: 1986 Dodge Ram 50 360 swap

  1. #51

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Quote Originally Posted by travhous View Post
    Original brake lines, only thing I added was one short section of steel line to the line lock and everything is uncut and oem.

    To mount the Stealth's brake booster I had to drill two holes in the firewall for the lower studs. Used the Stealth's aluminum spacer between the booster and firewall and the brake pedal line up perfectly.
    I did a similar thing to install the BMC out of a Gen 3 (think it was a Gen 3...) Pajero. The 2 top brake booster studs lined up with the steering column/brake booster brace holes. I cheated a little by using the Gen 3 brake booster spacer and used the bottom through holes as a drill guide and went through the firewall with a new 8mm HSS drill bit (I dummied the spacer in place with 2 x 8mm bolts and flange nuts so the spacer was held exactly where I needed it) Had to do some sketchy free hand bending of the existing solid brake lines, but it appears to have worked fine.

  2. #52

    Array
    Status
    Offline
    Join Date
    09-05-2018
    Posts
    79
    Location

    Christiana, PA
    Vehicle

    1986 Dodge Ram 50
    Engine

    Dodge V8
    Building custom headers and have one side pretty much finished up. Went with a tri-y design just to simplify things and there just isn't much room to work with. I purchased cheap stainless headers off eBay and cut them up to build these. Much cheaper than buying all the tubing, got a few sets for around $45 a piece.

    IMG_20200112_015134.jpg
    IMG_20200112_015051.jpg

  3. #53

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    ...and they'll probably be better finished compared to how you got them. Nice work! I have a similar idea to use headers from an NA Talon if I ever get the chance to go twin cam. I can get them relatively cheap but the freight will burn me.

  4. #54

    Array
    Status
    Offline
    Join Date
    01-09-2020
    Posts
    514
    Location

    Cant Say
    Vehicle

    1987 Dodge Power Ram 50
    Engine

    Dodge V6
    how did you fit that? i saw a 302 swapped MM but a 360? that thing is huge, a 318 block is like twice the size. thats so cool

  5. #55

    Array
    Status
    Offline
    Join Date
    12-10-2015
    Posts
    177
    Location

    Wichita Falls, Texas
    Vehicle

    1991 Mitsubishi Mighty Max
    Engine

    4G64
    Question regarding your gauges. Are you able to use the factory speedometer? If so what did you need to do to keep it?

  6. #56

    Array
    Status
    Offline
    Join Date
    09-05-2018
    Posts
    79
    Location

    Christiana, PA
    Vehicle

    1986 Dodge Ram 50
    Engine

    Dodge V8
    Quote Originally Posted by t97 View Post
    Question regarding your gauges. Are you able to use the factory speedometer? If so what did you need to do to keep it?
    My truck was originally equipped with the baby 904 automatic transmission which is nearly the same as the v8 904. Original speedometer cable hooks right up, just had to swap the speedo gear in the transmission.

  7. #57

    Array
    Status
    Offline
    Join Date
    09-05-2018
    Posts
    79
    Location

    Christiana, PA
    Vehicle

    1986 Dodge Ram 50
    Engine

    Dodge V8
    Getting more fabricating done.


    IMG_20200117_113622.jpg
    Cut outs for the exhaust.

    IMG_20200126_141834.jpg
    IMG_20200126_141922.jpg
    IMG_20200126_141908.jpg
    Truss for the rear axle housing. I'm curious how far I can push the the stock differential and just trying to save a couple dollars.

    IMG_20200122_213736.jpg
    New exhaust tips and put the rear bumper back on for more rear weight. Took the bumper off over 25 years ago and I actually like the look of it back on the truck.

  8. #58

    Array
    Status
    Offline
    Join Date
    09-05-2018
    Posts
    79
    Location

    Christiana, PA
    Vehicle

    1986 Dodge Ram 50
    Engine

    Dodge V8
    Headers wrapped and installed, ended up taking few days to build both sides. First time building headers and they are a tight fit.
    IMG_20200129_090706.jpg
    IMG_20200129_090932.jpg

  9. #59

    Array
    Status
    Offline
    Join Date
    01-09-2020
    Posts
    514
    Location

    Cant Say
    Vehicle

    1987 Dodge Power Ram 50
    Engine

    Dodge V6
    if that were my truck i would have chrome bumper under it, but thats just an opinion. i really like it. i love these little trucks and i want to do so much with mine but i cant, so right now i am looking at a 1992 D50 2wd reg cab short bed to convert into a SRT4. i want to do a cummins swap on a power ram. might do it with the 82 and a clapped out cummins just for shits and giggles

  10. #60

    Array
    Status
    Offline
    Join Date
    01-09-2020
    Posts
    514
    Location

    Cant Say
    Vehicle

    1987 Dodge Power Ram 50
    Engine

    Dodge V6
    btw i love the headers. what does wrapping them do?

  11. #61

    Array
    Status
    Offline
    Join Date
    09-05-2018
    Posts
    79
    Location

    Christiana, PA
    Vehicle

    1986 Dodge Ram 50
    Engine

    Dodge V8
    Quote Originally Posted by Salteen View Post
    btw i love the headers. what does wrapping them do?
    Keeps more heat inside the tubes, hotter gases flow faster. Also lowers under hood temperatures.

  12. #62

    Array
    Status
    Offline
    Join Date
    01-09-2020
    Posts
    514
    Location

    Cant Say
    Vehicle

    1987 Dodge Power Ram 50
    Engine

    Dodge V6
    oh ok, might do that to my G54B when i get the turbo on it

  13. #63

    Array
    Status
    Offline
    Join Date
    06-15-2014
    Posts
    6,059
    Location

    Adelaide, South Australia
    Vehicle

    1985 Mitsubishi L200
    Engine

    G63B
    Awesome stuff travhous Good to see someone going all in and making sure it's done right. The header wrap is a good idea, especially with how tight you've got the headers up against the engine. Would've been challenging to get it all together.

  14. #64

    Array
    Status
    Offline
    Join Date
    10-22-2015
    Posts
    519
    Location

    Nevada
    Vehicle

    1990 Mitsubishi Mighty Max
    Engine

    Other
    Nice custom work going on there.

  15. #65

    Array
    Status
    Offline
    Join Date
    09-05-2018
    Posts
    79
    Location

    Christiana, PA
    Vehicle

    1986 Dodge Ram 50
    Engine

    Dodge V8
    I had to replace the transmission and decided to do some improvements on my tranny mount. I thought I would share what I think is a easy solution for the 1st Gen crossmember if you're doing this sort of swap. Find a 2nd Gen crossmember and things should be much simpler. The second generation has a pad welded to the rear of the crossmember compared to the first generation where the trans mounts right in the center. If running a 904 tranny the stock automatic mount should bolt right up. I tried to run the first gen mount and it was not nearly strong enough for the v8 swap. I'm going to stick with the crossmember I have been using because I would have to many things to change like exhaust and etc... But if I had to do it again I would use the gen 2 crossmember and hope this might help someone doing the same kind of build.IMG_20200326_182358~2.jpg

  16. #66

    Array
    Status
    Offline
    Join Date
    09-24-2019
    Posts
    235
    Location

    Nevada
    Vehicle

    1991 Dodge Power Ram 50
    Engine

    6G72
    Really like the attention to detail.

  17. #67

    Array
    Status
    Offline
    Join Date
    01-24-2017
    Posts
    1,219
    Location

    New Zealand
    Vehicle

    1981 Mitsubishi L200
    Engine

    Other
    i gotta measure up that 2nd gen trans cross member and see if it will work with mine

  18. #68

    Array
    Status
    Offline
    Join Date
    01-09-2020
    Posts
    514
    Location

    Cant Say
    Vehicle

    1987 Dodge Power Ram 50
    Engine

    Dodge V6
    Well, how is it going?

Page 3 of 3 FirstFirst 123

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •